Standard operational procedures

This is a list of concise, preferred operational practices for X-Dimension. For detailed descriptions of systems, please see Systems Descriptions. David Collins, the previous owner, wrote the Manual Of Useful Information.

Rigging

Mainsail

Set

• Hoist lazy jack lines. Ensure that they are not snagged on blocks or other fittings on the boom.
• Remove sail ties after hoisting lazy jacks.
• Ease the main sheet slightly, disconnect the main halyard from the boom end and attach to the head of the mainsail
• Optional: assign a crewmember to haul the main halyard at the mast
• Ensure that the mainsheet and boom vang are free
• Head into wind
• With a couple of wraps of the halyard around the starboard cabintop winch, a crewmember will hoist the main.
• A crewmember at the mast can assist by jumping the halyard.
• Hoisting crew must keep an eye on the leech of the sail to ensure it doesn't snag on the lazy jacks.
• Note: The main sail can be hauled to its full height by a sailor of moderate strength and certainly by two working together. DO NOT use the winch to haul it up - binding is usually due to the halyard being fouled, a sail tie being left in place, or other problem. In these cases, use of the winch will risk breaking the rigging.
• Once the mainsail luff is fully extended, tighten the luff to the desired tension using the winch

Close-Hauled Trim

• Set the traveler slightly to windward so that with the mainsheet tight, the boom is on the centerline
• Trim the mainsheet so that the top telltale on the leech alternately streams back and curls to leeward
• Note: When close-hauled, the jib tends to backwind the main, creating a slight bubble in the mainsail luff. This is normal.

Reaching or Running Trim

• If the boom is over the traveler rail, the mainsheet has much more mechanical advantage than the boom vang and should be used as the primary sail shape control
• If the boom is outside of the traveler rail, the boom vang should be used to control the mainsail shape
• When broad reaching or running, the preventer (located in the starboard lazarette) should be attached to a bail on the boom and the toe rail and tightened as needed

Reefing

• Station two crewmembers (with one winch handle) at the forward end of the boom on the starboard side
• Station one crewmember at the main halyard winch
• Place outhaul line in jam cleat, then remove outhaul line from cleat and boom winch
• Get reefing line (usually cleated on other side of boom from winch) and put two wraps of the reefing line around the boom winch
• Ease the mainsheet to depower the mainsail (head the boat to wind if necessary)
• Ease the main halyard, bring the mainsail luff down, and engage the reef cringle on the reefing horn
• Tighten the main halyard; one crew member at the mast helps with halyard, the other observes and calls to the halyard crew members when the luff tension is correct
• Using the winch on the boom, tighten the reefing line until the reef clew is brought down tight against the boom - cockpit crew calls this to the mast crew
• Secure the reefing line on a cleat on the boom
• Trim the mainsail as desired
• Shake out the reef by reversing the procedure

Douse

• Remove the lazy jack lines from underneath the reefing horn, tighten and cleat the lazy jack halyard, ensuring that the lazy jacks are in place to catch the mainsail
• Station two crewmembers on each side of mast at the gooseneck and one at the main halyard winch
• Station a third crewmember with sail ties a the ready at the end of the boom on the cabin top (Note: it is helpful to close the companionway hatch so this crewmember can work safely
• When the boat is head to wind, ensure that the mainsheet and boom vang are free
• As the halyard is slowly eased, the crewmembers at the mast alternately flake the mainsail luff to port and starboard
• At the same time, the crewmember at the boom end flakes the mainsail leech, pulling aft at each flake and attaching sail ties
• Note: The crewmember at the halyard should be watching the flaking process to ensure that she is easing the halyard at the appropriate rate.
• Once the mainsail is completely lowered and all ties are in place, the main halyard can be removed from the mainsail head and attached to the boom end
• Ensure that the mainsheet and boom vang are free, then MANUALLY haul the main halyard to level the boom and secure the halyard
• Note: DO NOT use the winch to level the boom with the halyard. Recruit a crewmember if necessary to lift the boom. If the boom is stuck, diagnose the problem. It is usually a fouled mainsheet, main halyard, or boom vang and use of the winch will may break the rigging

Genoa

Set

• Free the jib sheets and put two wraps of the working sheet on the primary winch
• Free the black furling line and fake it down so that it will run without fouling
• Station one crewmember on the furling line, another at the working sheet, and a third with a winch handle at the ready
• While the sheet trimmer hauls on the working sheet to unroll the genoa, the crewmember with the furling line should control it so that the line pays out smoothly and under control. Do not allow the sail to unroll violently. In strong wind, it can be helpful to put a bight of furling line around a cleat to help control it.
• Sheet in the genoa to achieve the desired shape
• Secure the furling line
• Note: When reaching or running, the genoa sheets should be lead outboard of the shrouds through the snatch blocks on the rail (make sure that the sheets do not foul on the lifelines). When close-hauled, the genoa sheets should be led inboard of the shrouds through the sheet blocks on the tracks outboard of the cabin top
• Note: Before tacking and jibing, make sure that the lazy sheet is not fouled on one of the winches on the forward cabin top or on the forward hatch

Douse

• Assign a crewmember to the furling line and another to control the sheets. In strong winds, two crew members may be necessary on the furling line.
• Ease the working sheet to depower the sail
• While one crewmember hauls on the furling line, the other puts slight tension on the genoa sheets to ensure that the sail is tightly furled. To aid in furling, alternate back and forth: slack the sheet while the furling line is hauled, then tighten up the sheet while the furler pauses between heaves.
• Keep furling until there are two wraps of the sheets around the furled sail.
• Note: DO NOT use a winch on the furling line as you will risk breaking the furling mechanism, the turning blocks, and/or the stanchions

Asymmetric Spinnaker

Set

• Note: If the course is well off the wind, rig a mainsail preventer
• Pass spinnaker bag up through forward hatch and clip base of bag to lower lifeline on foredeck on side to which spinnaker will be set
• Note: Be sure that tack end of bag (green velcro tab) is facing forward. If necessary, open spinnaker bag and check that tack is forward (tack and clew are labeled on the sail)
• Remove spinnaker sheets from bag and attach snap hooks to sail clew.
• Rig spinnaker sheets outboard of shrouds and lifelines, through turning blocks on taffrail to the secondary winches
• Note: Be sure that spinnaker sheets are routed outboard of jib sheets
• Ease tack pendant line enough to clip on to spinnaker tack.
• Note: Be sure that tack pendant runs inside of bow pulpit and outboard of headstay
• Ease spinnaker halyard and attach to spinnaker head
• Free the snuffing line and flake it down on the deck. Be sure it is not tangled in the sail or running rigging
• Note: Be sure that spinnaker halyard runs outboard of the jib sheets
• Double check spinnaker rigging to be sure that it will run clear
• Assign one or two crewmembers to handle the tack pendant line at its winch
• Assign one or two crewmembers to handle the working sheet (ensure that the lazy sheet is free)
• Assign one or two crewmembers to handle the spinnaker halyard
• Assign a crewmember to feed the spinnaker out of its bag and control the snuffing line
• Pre-brief all crew on the operation
• The helmsman should steer for an apparent wind angle (AWA) of about 110 degrees (light air) to 130 degrees (heavy air)
• Note: These AWA figures may not be as critical when using the snuffer
• The crewmember on the tack pendant should tension the pendant so that the tack will be just above the bow pulpit
• Hoist the snuffed sail until the head is tight at the masthead. Avoid excessive tension with the winch as the halyard can foul in the sheeve.
• The crewmember on the snuffing line should haul the side of the line not attached to the snuffing "funnel" so that the snuffer retracts along the sail toward the masthead.
• The crewmember on the working sheet should trim smoothly as the sail unsnuffs so that the sail fills evenly. Do not oversheet as this can cause excess tension on the leech as it pays out of the snuffer
• When the snuffer is fully retracted and the sail fills, ease the sheet to obtain a slight hook in the luff
• Secure the snuffing line at the base of the mast
• As the luff approaches the headstay, the tack pendant can be eased to achieve the proper sail shape
• The helmsman should keep the boat at a constant AWA throughout the set
• Note: Clear communication is very important. There should be one and only one person in charge during spinnaker operations. It is best if this person is not one of the crewmembers setting the sail or the helmsman

Flying

• The sail trimmer should be positioned at or near the windward shrouds where she can see the luff
• The sheet should be led from the secondary winch, across the cockpit, where it can be held by the sail trimmer
• A crewmember should be at the winch to grind when the trimmer calls for it - the trimmer will tail the sheet as necessary
• The trimmer should trim and ease as necessary to keep a slight hook in the luff of the sail
• The helmsman should keep a steady course and alter it only with clear communication with the trimmer
• When on a close reach, trimming may be insufficient to recover a collapsing sail. In this case, the trimmer should call for the helmsman to fall off slightly

Douse

• Assign crew to the tack pendant, and the snuffing line
• Bring the tack down until it is just above the bow pulpit
• Free the snuffing line from the base of the mast
• Ease the sheet to depower the sail and haul down the snuffing line on the side where it attaches to the "funnel"
• As the snuffer approaches the foot of the sail, ease the tack pendant to allow the foot and the snuffer "funnel" to be brought inboard of the lifeline and placed in The spinnaker bag.
• If the winds and seas are light, attach the tack and clew to the spinnaker bag and then flake the snuffed sail into the bag as the halyard is eased
• If the winds and seas are heavy, bring the snuffer down on deck under control, then place in the bag
• Attach the head to the spinnaker bag and secure the halyard at the base of the mast
• flake the snuffing line into the spinnaker bag
• Coil the spinnaker sheets and place in the spinnaker bag
• Close the bag and pass it down the forward hatch

Tacking and Jibing

• Assign crew to the tack pendant, and the snuffing line
• Bring the tack down until it is just above the bow pulpit
• Free the snuffing line from the base of the mast
• Ease the sheet to depower the sail and haul down the snuffing line on the side where it attaches to the "funnel"
• As the snuffer approaches the foot of the sail, ease the tack pendant to allow the foot and the snuffer "funnel" to be brought inboard of the lifeline
• Detach the tack pendant, reroute it to the other side of the headstay, and reattach it
• Move the snuffed sail through the foretriangle to the other side of the foredeck
• Unsnuff and fly the sail per the normal setting procedure

Engine

Starting

• Transmission must be in neutral (port lever horizontal)
• Starter battery switch in starboard lazarette switched on (12 o'clock); buzzer will sound
• Throttle (starboard lever) up slightly
• Assure engine stop control (T-handle) is in run position (pulled up)
• Press black starter button (with rubber boot starboard of the binnacle)
• Throttle down to idle after engine starts
• Check oil pressure gauge to ensure pressure rises after start
• Check exhaust to ensure cooling water is being expelled.

Shifting

• Throttle must be at idle before shifting (starboard lever down)
• Transmission settings (port side lever): ahead propulsion(lever down), astern propulsion (lever up), neutral (lever horizontal)

NOTE: FAILURE TO SET THROTTLE AT IDLE BEFORE SHIFTING WILL DAMAGE PROPELLER FEATHERING MECHANISM

Stopping Engine While Under Sail (to feather propeller)

• Transmission must be in ahead propulsion (port lever down)
• Boat speed must be at least 5 knots through the water so that prop feathers when engine stops (use throttle as necessary to supplement sails)
• Keeping transmission in ahead propulsion, push engine stop control (T-handle) to down position; engine will stop and buzzer will sound
• Starter battery switch in starboard lazarette switched 'off' (9 o'clock); buzzer will silence
• Move transmission lever to neutral (port lever horizontal) to prepare for next start
• Visually check prop shaft (can be viewed easily from starboard lazarette opening); if rotating quickly, then prop has not feathered and process must be repeated at a higher boat speed. If rotating slowly, place transmission in astern propulsion to stop rotation.

NOTE: If engine is stopped while in astern propulsion, the propeller will not feather.

Stopping Engine

• Transmission in neutral(port lever horizontal)
• Throttle at idle (starboard lever horizontal)
• If engine has been running hard and is hot, allow to idle for a few minutes to cool before stopping engine
• Push engine stop control (T-handle) to down position; engine will stop and buzzer will sound
• Starter battery switch in starboard lazarette switched 'off' (9 o'clock); buzzer will silence

Electrical

X Dimension has two separate 12-volt systems, "Engine" and "House". The Engine system, including the Engine Battery, is used for starting the engine and powering the engine instruments and the electric fuel pump. The "House" battery powers all the other 12-volt systems onboard. When the engine is running, both battery banks are charged through a battery isolator.

• The top three breakers above the galley sink are designated "always-on" breakers and are to be left ON at all times:
  • Bilge Pumps - directly power the bilge pumps from the House battery
  • Engine - supplies power to the starter solenoid and engine instruments
  • Fuel Pump - supplies power to the inline fuel pump

Engine Battery

The Engine Battery Switch is a black rotary switch located on the forward bulkhead inside the starboard lazarette (as of 8/15/2012. This switch may be moved to inside the main cabin in the near future). This switch has two positions, ON (12 o'clock) and OFF (9 o'clock). When turned on, the Engine Battery supplies power to the inline electric fuel pump through the "Fuel Pump" breaker, and to the starter solenoid and engine instruments through the "Engine" breaker. Note that when the switch is first turned on, you should hear the low-oil-pressure buzzer sound until the engine is started.

The "Engine" always-on breaker supplies power to the starter button, tachometer, water pressure gauge, and buzzer on the cockpit instrument panel (the oil pressure gauge works hydraulically). The buzzer is connected to a low-oil-pressure switch and an over-temp switch on the engine, so the buzzer will sound if the oil pressure is too low or if the engine water temperature is too high.

The "Fuel Pump" always-on breaker powers an inline electric fuel pump located in the lower port berth, just aft of the fuel tank. The mechanical lift pump on the engine has a leak, so without positive pressure from the electric fuel pump, air will get into the fuel lines and the engine will stop.

The alternator's charging current is regulated by an external HEHR Powerline regulator, mounted on the forward bulkhead in the starboard lazarette (next to the fire extinguisher). The HEHR regulator has four LEDs:

• ORANGE: Field signal (should flicker)
• RED: Low voltage
• YELLOW: Stator signal (should flicker)
• GREEN: Power (should be steady green)

If the red low voltage LED is illuminated, then the alternator voltage is too low for proper charging of the batteries. Increase the throttle until the red LED turns off to properly charge the batteries.

House Battery

The House battery bank is located in the starboard lazarette, under the white wooden winch handle tray. Note that in the Fall of 2011, there were two house batteries tied in parallel to make a single house battery bank. In Summer of 2012, the bank consists of only one battery.

The House Battery Switch (black rotary switch under the volt meter) should be turned to "HOUSE" to use the 12-volt systems onboard and to enable charging of the House battery bank.

Do not turn the House Battery switch to "both" or "2" except in the case of an emergency (see below)

The House Battery Switch supplies power to all of the breakers above the sink, except the top three "always on" breakers:

• Navigation Lights Master - supplies power to the navigation lights sub-panel
• Navigation Instruments - supplies power to the GPS, depth sounder and wind instruments.
• VHF Radio
• Radar
• Horn (horn button is on starboard side of binnacle)
• Freshwater Pump
• Cabin Lights
• Footlights
• Fridge
• Propane (not installed as of 8/15/2012)
• Bilge Blower
• Aux 12-volt Outlets (not installed as of 8/15/2012)

The Navigation Lights Sub-Panel is a gray plastic switch panel that is located above the galley sink near the regular breakers (as of 8/15/2012. This panel may be moved to the cockpit in the near future). When powered on by the "Navigation Lights Master" breaker, the switch labels should glow red. When a switch is turned on, it will glow green. If the label does not glow, then the internal fuse for that switch may be blown.

• Running Lights - Includes sidelights (in the bow) and stern light
• Steaming Light - The white forward-facing "masthead light" halfway up the mast.
• Tri-color - at the top of the mast (Note: do NOT use tri-color with running lights or steaming light)
• Anchor Light - White all-around light at the top of the mast
• Foredeck Light - Halfway up the mast
• Instrument Lights - Powers cockpit instrument panel lights and compass light

The voltmeter above the House Battery Switch can be used to check the voltage on the House battery (flip the switch to the left) or the Engine battery (flip the switch to the right). Note that the corresponding battery switch must be turned on for the voltmeter to make an accurate reading.

Bilge Pumps

Power to the bilge pumps is supplied directly from the House battery bank, through the always-on "Bilge Pumps" breaker. Note that this bypasses the House battery switch.

• Each pump is controlled by one of two rocker switches next to the nav station table.
• Each switch has three positions, "Manual", "Off", and "Auto"
• Each rocker switch contains a fuse for the pump

Both switches should normally be left in "Auto" mode. This only activates the pump when the water level in the bilge is high enough to activate that pump's corresponding float switch. The pumps can be tested by toggling the corresponding rocker switch to "Manual". When a pump is running, the a dim red light should glow on the rocker switch.

Note that the top rocker switch corresponds to the forward most pump and the forward most float switch.

Navigation Instruments

The Garmin GPSMap541 uses the GPS antenna mounted on the stern pulpit. It communicates with the GM10 display unit, the depth sounder, and the wind instruments at the top of the mast through an NMEA2000 network. Many different parameters can be displayed in digital or analog form on the two cockpit displays. The standard display can be show by pressing the following button sequence:

• press HOME
• select "Charts" with the arrow keys, then press SELECT
• Select "Navigation Chart" with the arrow keys, then press SELECT

Please read the owners manuals for the GPSMap541 and the GM10 (located in the documentation folder inside the navigation table) for more detailed operation of these units.

Note that the GPSMap541 also sends longitude and latitude data to the fixed-mount VHF radio through an NMEA0183 interface.

VHF Radio

The fixed-mount VHF radio is connected to an antenna at the top of the mast. Channels are selected using the up/down keys on the unit, or the up/down buttons on the handheld mic.

The radio receives latitude and longitude data from the Garmin GPSMap541. A "satellite" icon will appear on the front panel of the radio if it is correctly receiving coordinate data from the GPS.

In a life-threatening emergency, an automatic distress call can be initiated by lifting the hinged red plastic cover labeled "Distress" and holding down the button for five seconds. This should send out a digital distress call and then switch the radio to channel 16. You must also make a voice Mayday call on channel 16.

For more details about operation of the VHF radio, please see the owners manual (located in the documentation folder inside the nav station table).

Galley

Lighting Galley Stove

• Open valve at top of propane tank (located in Port Lazarette)
• Switch on electrical panel above galley sink to 'on'
• Switch on bulkhead above galley stove to 'on' (Note: pilot light on switch inoperative)
• Light butane lighter or strike match
• Press in control knob for desired burner on stove and turn to light position
• Light burner
• Hold in knob for about 20-30 seconds then release

NOTE: Turn off both electrical switches and close valve at top of propane tank after each use