Difference between revisions of "Mashnee task list"

From MITNA
Jump to: navigation, search
m
(Sails and canvas:)
 
(111 intermediate revisions by 2 users not shown)
Line 3: Line 3:
 
Please use the discussion page to discuss the prioritization and content of any of these tasks.
 
Please use the discussion page to discuss the prioritization and content of any of these tasks.
  
== Pre-storage (fall) tasks ==  
+
==Sailing Season Projects==
* Lay out all sails and look for any issues
+
* Dry the spare lines, spinnakers, and anything else that’s wet, especially if they will be stored somewhere without air circulation
+
* Inspect all lines, rig hardware, and spars before storing them for the winter
+
* Inspect and inventory safety gear, medical kit, etc.
+
* Inventory spare parts and make list of needed replacements
+
* Scrub bilges around engine with Joy to remove fuel leak residue
+
* Remove knives -- Gavin to resharpen
+
  
Organize bins:
+
==2024-25 Offseason work ==
* Kitchen stuff
+
* Foulies
+
* PFDs + tethers
+
* Books / charts / nav equipment + medical kits + safety equipment
+
* Cleaning supplies
+
* Lines
+
* Spares from under the forward berth
+
  
= Dion's Work =
+
Observations are listed on Discussion page
==Centerboard==
+
*Plan is to pull the board right away when hauled.
+
*Grind off head until it swings easily through wood on top of the lead keel while swelled up. Put the boat back into water to make certain it swings freely with the box wet and swollen up. Remove board again and glass up properly and install downhaul line up through the tube to the cabin top as well. New bright red paint.
+
*Get 1" half oval from Hamilton for Gasket Plates. Two 8' pieces... Cut to fit. Drill and counter sink for 1/4" screws on drill press. Install gasket beneath. Mark edges then, remove and re-cut gasket with hot knife. Then finally install...
+
  
== Rigging, Hull, Motor ==  
+
===Hull and woodwork:===
* Replace spreader lights - convert to LEDs with lower profile, mount them better. Dions
+
*Renew varnish: especially bowsprit, toerail, tiller, mast (Dions)
* We need a new (3rd) cowl vent, one went missing at the start of the season. Dions
+
*Renew paint below waterline (Dions)
* Inspect all standing rigging, grease Furlex bearings top and bottom
+
*Renew paint above waterline (likely ok for another season)
*  All the hatch hinges need to be strengthened, replaced and/or repaired. We had water intrusion and loss of almost all of them this year (I think it was time catching up to them?) Dions
+
*Inspect tiller and rudderpost to diagnose odd feeling (Dions)
* The forward hatch teeth (the part attached to the hull that the latch goes in) needs to be re-attached. Thru bolted in bronze pls Dions
+
*Repair skylight hatch (functionality – Dions)
* The whole inside of the hull needs to be gone over, especially in the cockpit lockers. There was significant mold/mildew buildup. (We did a first round in November. Dions in Spring?)
+
*Shave down companionway boards so they don’t stick (functionality – Dions)
* Scrub bilges around engine with Dawn or Joy to remove fuel leak residue (we can also do this)
+
*Plane edges of floor boards so they don’t stick (safety - Dions)
* Create a way to hold the lid under the forepeak berth open when rummaging for supplies. Dions
+
*Move brass hook for chartplotter (Dions?)
* Topsides touch-up again? Re-paint next year? Check plank ends at transom, please.
+
*Hatch top compass mount (Gavin)
* Bottom paint, What brands are best? Sea Hawk?
+
*Porthole screen covers (Ted)
* Varnish- Cabin top, toe rails, coamings, tiller, companionways, hatches, spars- Interior surfaces?
+
* Winterize engine and all water systems
+
* Motor- Change oil and filter. Leave spare filter on board
+
* Replace low-pressure engine oil line near on-engine fuel filter that has a nick and slow oil leak. It is getting worse. (+ reattach to prevent chafe; check other lines for potential chafe).
+
* Check forward starboard engine mount- seems off
+
* Polish fuel tank- Boat should arrive with less than 1/3 tank
+
* Purge water systems and flush/ bleach
+
* Fresh o rings and gaskets on fuel fill, fresh water fill and holding tank
+
* Flush and purge poop tank? Boat arrived mostly pumped out
+
* Replace or repair two bent stanchions
+
  
= North Work =
+
===Sails and canvas:===
* We need a new canvas boot for the mast-deck connection. North.
+
*Sail repairs at North:
* Two little covers for furler line port. North
+
**95: tears in luff boltrope, detaching spreader patch
* 140 work: Luff tape torn, need to buy a pre-feeder, Shorter aft batten along 140 foot
+
**160: boltrope separating at head, small cuts near foot
* Big red spin- tear near clew repaired
+
*Replace main sail cover (North/Wally)
* Mainsail cover inspected and repaired as needed
+
*Repair cabin top cover (North/Wally)
 +
*New mast boot cover (Libby?)
 +
*Minor sail repairs per observations on discussion page (MIT)
 +
*Price out sail improvements (Adam)
 +
**UV strip for 95
 +
**Recutting foot of main to raise boom in cockpit ~8 inches
 +
**Recutting 140 to 120
 +
**Cruising 95 with no battens, UV strip
  
= Other outsource =  
+
===Rigging:===
*Code Zero - must work with current hardware. Sleeve - to fit cable.
+
*Check discoloration under forestay tang spacer on mast for rot; re-bed spacer block so water can’t collect (safety – Dions)
*New #3 jib?
+
*Seal loose fibers at heel of mast against rot (safety – Dions)
* Second spinnaker halyard done properly - consistent in diameter
+
*Check wire rigging for deterioration (spiraling rust color) (safety - Dions)
* Replace dyneema topping lift?
+
*Check condition of bronze on chain plates below deck (safety - Dions)
 +
*Running rigging replacement/maintenance (Libby)
 +
*Fix springs in jib car pins
 +
*Grease sticky winch handle (and service winches?)
 +
*Top cap for furler foil
 +
*Gear for spinnaker peels (Adam)
 +
*Jib furling line to cockpit (wish list)
 +
*Messenger lines for halyards (wish list)
  
= MIT Work =  
+
===Engine:===
 +
*De-sludge fuel tank and clear out remaining water (Dions, or Dion’s recommendation)
 +
*Change raw water impeller (Dions)
 +
*Oil and filter change (Dions - underway)
  
== Random Work ==
+
===Systems:===
 +
*Winterize and clean head and water systems (Dions)
 +
*Unclog galley sink (Ted)
 +
*Clean speed paddle wheel (Ted)
 +
*Price doppler boat speed alternative (Ryan)
 +
*Wireless instrument broadcast (Adam)
 +
*Find wireless instruments
 +
*Backup nav lights (Adam)
 +
*Check wind index for bird damage (Dions?)
 +
*Put batteries on trickle charger?
 +
*Download B&G data (Adam)
  
* Buntlines for main sail reefing (these are the lines that pass through the grommets in the sail)
+
===Gear:===
* Bungees on head hatch - Gavin
+
*Retube or replace dinghy (essential - Gavin/Stew)
* Mounting for compass? New compass?
+
*Inspect and maintain life vests (essential - Libby)
 +
*Check/replace safety gear (essential – Libby)
 +
*Wash rain gear (Scott)
 +
*Wash cushion covers (Scott)
  
== Sails==
+
===Admin:===
 +
*2025 registrations for dinghy and Mashnee (Stew)
 +
*2025 Ratings: PHRF and ORREZ (Adam)
  
* Working jib - bolt rope on the luff frayed near the head - maybe not needed if replacing?  
+
===Shopping List===
* Stitch zipper stops for all sail bags
+
*Green bulbs for running lights: Makergroup 1076 1142 1004 90... https://www.amazon.com/dp/B088GT8QKC?ref=ppx_pop_mob_ap_share
 +
*Replacements for expired flares
 +
*Replacements for med kit
 +
*Boathook
 +
*Deck brush
 +
*Sea Sucker
 +
*Loos gauge for shroud tensioning
 +
*Spare O rings, clearly labeled (Gavin/Ryan)
  
==Rigging==
 
* Replace jib sheet - same diameter, length + 1' - maybe just fix?
 
* Whipped jib sheet ends
 
* Replace or end for end the main sheet
 
* Cunningham purchase system to easily be soft shackled on when needed - carabiner?
 
* Longer jib furling line to let us lead it aft? Soft shackle fairlead?
 
* Winches broken down and greased - Gavin
 
* Jib prefeeder - us
 
* New cable for spinnakers
 
* Tack line hardware for attaching spin roller furler to a jamming bight - delay for now?
 
* Ring-dings for turnbuckles
 
* Replace all cotter pins
 
* Double smaller block for jib halyard. - Us
 
  
== Shopping List ==  
+
==Completed Tasks==
* purchase some of those blue grippy gloves or similar for the boat to have for people to use
+
MIT
* Purchase more sail ties that are extra-long -- webbing -- Fran
+
*Clean the dinghy motor propeller (October 2024 LM)
* Procure more hand sanitizer for onboard use
+
*Fix Running Lights (11-11-2024 SW)
* Procure more hangers for the foulies (maybe wood? or stronger plastic)  
+
**Replace the starboard bow light (is this separate from fixing it for the season? Was not completed as a separate task)
* Procure origo dometic 3000 rubber gasket for top of fuel container - https://www.atlanticmarinesupply.com/product/dometic-environmental-3880036-00-rubber-gasket/
+
*Inspect Sails (Oct. 2024)
* Procure a few more mugs for onboard use
+
*Clean boat thoroughly (Oct/Nov 2024)
* Procure a metric socket set for onboard tasks (e.g. engine work)  
+
* Procure some chamois for proper clean-up
+
* Procure a pool noodle (or something else) for storing the battens
+
* Purchase new self-sealing washer for fuel stop solenoid and replace: Volvo Part 21424327
+
* Purchase Extra racor filters and a
+
  
==Miscellaneous==
+
Dions
* Handle to replace capstan? Get Fran a drawing
+
*Winterize engine (November 2024 Dions)
* Housing for the radar reflector—a bag or permanent hook or both
+
* Figure out anti-fouling for the dinghy motor (doesn't tilt far enough up to keep prop out of water).
+
* Anti-foul the dinghy bottom
+
* All the dinghy glue
+
* Replace eye for lee cloth on port berth
+
* Repair screen on the starboard porthole
+
* More permanent repair to companionway screen (+ better place to store)
+
* Replace flag on end of windex triangle
+
* Winch handle release issue -- can we fix this?
+
* Shave bilge panels for easier access?
+
* Grease companionway tracks
+
* Spruce up soundproofing around the engine
+
  
+
==Task Lists from Past Seasons==
==Radar and electronics==
+
* Base for radar mount?
+
* Full electronics meeting to follow. Radar/new MFD, etc? Both B&G and Raymarine reps just recommended getting a new raymarine radar. To replace the MFD we’d also need to replace a lot of the sensors around the boat.
+
* New Raymarine radar so that we can it to display on the chart plotter?
+
* Get rid of gremlins in the wireless displays (voltage boost?)
+
* Get touchscreen physical buttons properly working
+
* Get a new MMSI and reprogram everything so we don't conflict with "FUSION" on the west coast? -- AIS MOB, VHF, etc.
+
* Engine panel electrical gremlins - clean and reseat all contacts…
+
* Neaten up wiring to the chartplotter so that the "T" lives inside the cabinet
+
  
== Electrical ==
+
2023-2024: [[Task_List_2023-24|here]]
* High water bilge alarm should be rewired to also pump; right now if the lower switch fails the high water alarm will go off but the pump won’t run - Ted
+
* Cabin lighting -- LED and red/white option?
+
* Electrical panel -- replace LED "power on indicator" for running lights
+
  
==Safety==
+
2022-2023: [[Task_List_2022-23|here]]
 
+
* Some safety provisions for short-handed and/or night time sailing?
+
* SOP + pictures of jackline setup
+
* Encourage all to take a Safety at Sea seminar this winter.
+
* Procure 3 re-arm kits for PFDs
+
* Procure an 3rd water-activated light for 3rd throwable
+
* Procure a pair of safety glasses for the tool kit
+
 
+
==Mechanical==
+
* Create a video of changing and seating washers and gaskets properly?
+
* Check engine mounts -- stbd forward seems off
+
* Odd propeller sounds at high RPM. “Rumble” that’s off and 1/s oscillation sound.
+
* Purge water out of racor
+
 
+
 
+
== Spring (Pre-Launch) Tasks ==
+
* Manually inflate + inspect all PFDs
+
* Inventory + restock med kit
+
* Go over whole hull for mold/mildew
+
* Review all tools and service/replace any that are necessary and broken/too rusty
+
 
+
==Next summer==
+
*Training sessions
+
* Skipper dry run for jacklines + MOB
+
 
+
== Completed Tasks ==
+
* Re-rig reefing hook to sit closer to the boom -  Part is in the liquor locker drawers with a shackle on it.
+
* Wipe down all surfaces to reduce mold/mildew. (Used a mild bleach solution followed by freshwater wipe-down)
+
* Scrub overhead above refrigerator to remove mildew
+
* Remove PFDs, lines, [and all other moveable gear not needed by Dions to Bay 4 of the sailing pavilion]
+
* Remove all cutlery, plates, pots, etc.
+
* Inspected mainsail, working jib, 135 and 160 [11 Nov. 2022]
+

Latest revision as of 23:14, 19 November 2024

If a task needs additional explanation, please make a page for that task and post updates. When a task is completed, move it to the 'Completed Tasks' section, and include the date it was completed.

Please use the discussion page to discuss the prioritization and content of any of these tasks.

Sailing Season Projects

2024-25 Offseason work

Observations are listed on Discussion page

Hull and woodwork:

  • Renew varnish: especially bowsprit, toerail, tiller, mast (Dions)
  • Renew paint below waterline (Dions)
  • Renew paint above waterline (likely ok for another season)
  • Inspect tiller and rudderpost to diagnose odd feeling (Dions)
  • Repair skylight hatch (functionality – Dions)
  • Shave down companionway boards so they don’t stick (functionality – Dions)
  • Plane edges of floor boards so they don’t stick (safety - Dions)
  • Move brass hook for chartplotter (Dions?)
  • Hatch top compass mount (Gavin)
  • Porthole screen covers (Ted)

Sails and canvas:

  • Sail repairs at North:
    • 95: tears in luff boltrope, detaching spreader patch
    • 160: boltrope separating at head, small cuts near foot
  • Replace main sail cover (North/Wally)
  • Repair cabin top cover (North/Wally)
  • New mast boot cover (Libby?)
  • Minor sail repairs per observations on discussion page (MIT)
  • Price out sail improvements (Adam)
    • UV strip for 95
    • Recutting foot of main to raise boom in cockpit ~8 inches
    • Recutting 140 to 120
    • Cruising 95 with no battens, UV strip

Rigging:

  • Check discoloration under forestay tang spacer on mast for rot; re-bed spacer block so water can’t collect (safety – Dions)
  • Seal loose fibers at heel of mast against rot (safety – Dions)
  • Check wire rigging for deterioration (spiraling rust color) (safety - Dions)
  • Check condition of bronze on chain plates below deck (safety - Dions)
  • Running rigging replacement/maintenance (Libby)
  • Fix springs in jib car pins
  • Grease sticky winch handle (and service winches?)
  • Top cap for furler foil
  • Gear for spinnaker peels (Adam)
  • Jib furling line to cockpit (wish list)
  • Messenger lines for halyards (wish list)

Engine:

  • De-sludge fuel tank and clear out remaining water (Dions, or Dion’s recommendation)
  • Change raw water impeller (Dions)
  • Oil and filter change (Dions - underway)

Systems:

  • Winterize and clean head and water systems (Dions)
  • Unclog galley sink (Ted)
  • Clean speed paddle wheel (Ted)
  • Price doppler boat speed alternative (Ryan)
  • Wireless instrument broadcast (Adam)
  • Find wireless instruments
  • Backup nav lights (Adam)
  • Check wind index for bird damage (Dions?)
  • Put batteries on trickle charger?
  • Download B&G data (Adam)

Gear:

  • Retube or replace dinghy (essential - Gavin/Stew)
  • Inspect and maintain life vests (essential - Libby)
  • Check/replace safety gear (essential – Libby)
  • Wash rain gear (Scott)
  • Wash cushion covers (Scott)

Admin:

  • 2025 registrations for dinghy and Mashnee (Stew)
  • 2025 Ratings: PHRF and ORREZ (Adam)

Shopping List


Completed Tasks

MIT

  • Clean the dinghy motor propeller (October 2024 LM)
  • Fix Running Lights (11-11-2024 SW)
    • Replace the starboard bow light (is this separate from fixing it for the season? Was not completed as a separate task)
  • Inspect Sails (Oct. 2024)
  • Clean boat thoroughly (Oct/Nov 2024)

Dions

  • Winterize engine (November 2024 Dions)

Task Lists from Past Seasons

2023-2024: here

2022-2023: here