Difference between revisions of "(by person)"

From MITNA
Jump to: navigation, search
(Created page with "Edit to show progress... ==Greg:== * Repair keel - Greg. Greg has made good progress, Franny will push for him to complete the keel for launch. Greg should provide guidance w...")
 
(→‎Other:)
 
(43 intermediate revisions by one user not shown)
Line 3: Line 3:
 
==Greg:==
 
==Greg:==
 
* Repair keel - Greg. Greg has made good progress, Franny will push for him to complete the keel for launch.
 
* Repair keel - Greg. Greg has made good progress, Franny will push for him to complete the keel for launch.
−
Greg should provide guidance wrt bottom, mast/boom and topsides painting.
+
* Finish painting bottom.
 +
* Work on outhaul on boom
  
−
==Lloyd:==
+
==Adam:==
−
* Fix engine oil leaks - Lloyd. Lloyd says he’s on this; I’ll keep pushing him. No real Plan B if Lloyd doesn’t move on this; I think we need to pull the engine to do the job right.
+
* Repair dodger - Adam
 +
* Inflate red dinghy,  move to Waterboat.
 +
 
 +
==Ted:==
 +
* Inspect steering gear, grease rudderpost - Ted
 +
* Put batteries on boat
  
 
==Eric:==
 
==Eric:==
−
* Remove corrosion on mast and boom; repaint - Eric  We should work on the boom and the mast. No progress on this yet that I know of.
 
 
* Binnacle light - Eric (can be done after splash)
 
* Binnacle light - Eric (can be done after splash)
−
* Touch up topsides paint - Eric. Ditto wrt Greg. Our topsides Awlgrip color is Cabernet Burgundy as far as I can tell - Greg has a set of color samples. He might have a few touch-up kits; he said he would order a few last spring for this purpose. Buffing the topsides is part of this.
 
  
 
==Scott:==
 
==Scott:==
−
* Engine maintenance (change oil/various filters/replace raw water pump) - Scott.
+
* Replace nuts on rear quarter fittings ( 3 to go ) - Scott
−
* Replace nuts on rear quarter fittings - Scott
+
−
* New blocks for mainsheet - Scott  These are in hand.
+
−
* New shackles to fasten traveler adjusting blocks to car - Scott.
+
−
* Inspect running rigging - Scott.
+
−
* Take halyards/pfds/harnesses/jacklines/foulies/blocks/radios&plugs/puck compass/ditch bag/laptop/iPad to boat.
+
−
 
+
−
==Ted:==
+
−
* Replace damaged NMEA terminator for anemometer on masthead - Ted
+
−
* Inspect steering gear, grease rudderpost - Ted
+
−
* Condition batteries - Ted. I have no idea where this is at.
+
−
* Cetol woodwork - Ted. Scott applied a couple of coats of Cetol to the worst parts last Fall; we should put on a couple of coats more.
+
−
 
+
−
==Adam:==
+
−
* Repair dodger - Adam
+
−
* Remove, refurbish and reinstall fuel tank - Adam.
+
−
 
+
−
==Tim/Adam:==
+
−
* Paint bottom - Tim/Adam. This should be done with oversight from Greg - he knows how to do this really well and we do not (yet).
+
  
 
==Other:==
 
==Other:==
−
* Sails (new asym, re-cut #1 and #3, new #4, main with flattening reef). The sails are being finished up. Brad says the main.#1/#3 are ready to be picked up.
+
* Take cushions from pav to boat (shortly before launch)
−
* Take cushions from pav to boat
+
* Clean tools (use vinegar and scotchbrite; then spray with WD40)
−
* Take boom to boat
+
* Clean S/S engine pan, and hull underneath
−
* Inflate red dinghy, coat with ArmorAll, move to Waterboat.
+

Latest revision as of 14:41, 30 March 2016

Edit to show progress...

Greg:

  • Repair keel - Greg. Greg has made good progress, Franny will push for him to complete the keel for launch.
  • Finish painting bottom.
  • Work on outhaul on boom

Adam:

  • Repair dodger - Adam
  • Inflate red dinghy, move to Waterboat.

Ted:

  • Inspect steering gear, grease rudderpost - Ted
  • Put batteries on boat

Eric:

  • Binnacle light - Eric (can be done after splash)

Scott:

  • Replace nuts on rear quarter fittings ( 3 to go ) - Scott

Other:

  • Take cushions from pav to boat (shortly before launch)
  • Clean tools (use vinegar and scotchbrite; then spray with WD40)
  • Clean S/S engine pan, and hull underneath
Retrieved from "https://sailing.mit.edu/wiki/index.php?title=(by_person)&oldid=5734"