View source for Main Batteries Usage Strategies




This Guide gives guidelines for using the three main 12-volt batteries batteries in ways that protect the batteries and the engine's battery charger
	from harm, showing ways to keep the batteries charged and available for continued needs 
	of cruisers, and helping preserve the batteries' longevity. 

The guidelines are carried out by operating the two main 12-volt switches.
 

== Operation of 12-volt Main Switches ==

The two main 12-volt switches are under the nav-station seat.

Both switches have 4 positions; clockwise from their DOWN positions, the functions of each are OFF, #1, BOTH, and #2.

The top switch's #1 and #2 positions connect Battery #1 (the aft battery under the nav-station seat) and #2 (forward) respectively.

The top switch's #1 position connects Battery #3 (located forward of the engine), while its #2 position is a variant flavor of OFF.



== Synopsis of Rules: ==
   R01: NEVER turn all batteries OFF while the engine is running.
   R11: ALWAYS turn all three batteries OFF when leaving the boat.
   R12: NEVER have more than ONE battery ON when engine is not running.
        But is allowed when: R12RA: swap charging batteries; 
        R12B: when going power to sail; R12C: when all 3 are near-dead.
   R13: DON'T charge Batts #1/#2 at same time as Batt #3.

== Detailed Rules and Comments ==

'''Prime Directive:'''

   R01: NEVER turn all batteries OFF while the engine is running. 

:	Note: Doing so will likely cause  failure of the engine's alternator that charges the batteries.


'''Important Rules:'''

   '''R11:''' ALWAYS turn all batteries OFF when you leave the boat.

	Note: It isn't a disaster if one is left on, as long as all ship's systems are turned OFF;
they're turned OFF to prevent electrical fires aboard while the boat is unmanned.


   '''R12:'''	NEVER have more than 1 battery ON when the engine isn't running.

	Note: Doing so will often cause one battery to discharge into less-charged ones,
losing the optimal charge we may need to start the engine, and possibly 
putting stress on the batteries if one is a lot more charged than another.
	
Situations where we sometimes DO have two on at once include

:	  '''R12A:'''	When we want to swap from using, or charging, one battery to using or
charging another, we need to switch between them without breaking 
rule R01 for a millisecond (oh, I dunno, maybe actually 5, 10, 20 ms?). 
So to switch between 2 batteries controlled by a single main
switch, we merely turn between them by going through the "BOTH"
position of the switch.  

And if the two batteries are controlled
by two different main switches, the only practical thing is to
turn the new one ON first, and then as fast as possible (maybe 1 second)
turn the other switch's battery OFF.  

:	  '''R12B:''' A common scanario is when -- after running the engine awhile e.g. while
		motoring out from an anchorage or mooring, or when cruising in no wind --
		the crew turns off the engine and THEN, some minutes later, realizes they've 
		been charging two batteries.  There's no need to panic; both batteries may have
		been charged sufficiently and somewhat "equalized" that leaving them
		on together for 5 or 10 or so minutes should do no harm.

:	  '''R12C:'''	When all 3 batteries have become discharged, one can try turning
		two (or maybe even 3) batteries on together in order to crank the engine.


   '''R13:'''	Generally, don't charge either of Batteries #1 and #2 at the same time as Battery #3.

	The construction of Batteries #1 & #1 differs from that of Battery #3, and we
	assume that their charging regimens are different. 	

	Notes: Batteries #1 & #2 are "dual-purpose", designed for starting at high amperage AND/OR 
	for deep discharging (at a lower amperage) to run ship's electronic systems and lights.  
	These requirements imply that they're a compromise design for both of these usages,
	but for starting small engines and powering a modest amount of equipment to power 
	for hours, fitting a pair of these "dual-purpose" batteries is considered cost-effective,
	even though they are not optimized for either high-current for starting, or for
	being discharged deeply by lights, instruments, etc.

	Battery #3 is designed as a starting battery only; it is designed to withstand
	high starting currents, and is expected to get re-charged fairly quickly as soon
	as the engine is running.

== Other possible subjects: ==

* bilge pump is on batt#1, so it may want more charging if boat hasn't been sailed recently.

* Use of nav-station switch panel voltmeter to indicate battery charging or charged; use of engine control panel ammeter (not nav-station panel ammeter) for monitoring charging.